Bears Pool

Hot Tub Start-up Instructions for Bromine or Chlorine (bear Facts 3 Feb 09)

Hot Tub Start-Up Instructions For Bromine or Chlorine

VOLUME: 3. - FEBRUARY 2009

Spa Start-Up: Brominating Concentrate

First Time Start-Up

1. Fill your spa with water. If the make-up water is from a well or other  nonmunicipal source, testing prior to filling is recommended.
2. Super-oxidize the spa with Brominating Concentrate with spa circulation system  turned on. Run all pumps at least one cycle.
3. Operate the spa circulation system for at least 2 hours.
4.  Drain, then rinse interior surfaces and refill. Follow draining instructions in  owner’s manual. The reason for doing this is because spas are tested with water  and when they are shipped there is some water in the plumbing. By  super-oxidizing with a sanitizer during a pre-fill, you lessen the opportunity to contaminate the water with bacteria.

Refill Guide

1. Adjust pH (7.2-7.6), total alkalinity (80-120 ppm) and calcium hardness (100-200 ppm).
2. Apply Brominating Concentrate following label directions. Establish proper bromine residual of 3-6 ppm.

Daily Care

• If the hot tub is used daily Bromine Concentrate must be added after use, or at the end of the day.
•  If the hot tub is not used daily – Bromine Concentrate should be added every 3rd day.

Weekly Care

• Add Teddy Bear Stain and Scale Control.
• Apply Teddy Bear Water Clarifier.
• Test the pH. Acceptable range is 7.2-7.6. Ideal range is 7.4-7.6.
• Test total alkalinity of the water. Proper range is 80-120 ppm.

Monthly Care

• Test your water – Bring a sample to Teddy Bear Pools & Spas for analysis.
• Chemically clean your filter with Bear Strip Filter Cleaner.

As Needed

• Drain, clean, polish and refill based on usage.
•  If foaming occurs use Teddy Bear Anti-Foam.

Spa Start-Up: Chlorinating Concentrate

First Time Start-Up

1. Fill your spa with water. If the make-up water is from a well or other  non-municipal source, testing prior to refilling is recommended.
2. Super-oxidize the spa with Teddy Bear Chlorinating Concentrate with the spa circulation system on. Run all pumps at least one cycle.
3. Operate the spa circulation system for at least 2 hours.
4. Drain, then rinse interior surfaces and refill. Follow draining instructions in owner’s manual. The reason for doing this is because spas are tested with water and when they are shipped there is some water in the plumbing. By super-oxidizing with a  sanitizer during a pre-fill.

Refill Guide

1. Adjust pH (7.2-7.6), total alkalinity (125-150 ppm) and calcium hardness  (100-200 ppm).
2. Apply Teddy Bear Chlorinating Concentrate following label directions. Establish proper chlorine residual of 3-5 ppm.

Weekly Care

• Once spa is filled, start your spa. Add Teddy Bear Stain and Scale Control.
•  Apply Teddy Bear Water Clarifier.
• Test the pH. Acceptable range is 7.2-7.6. Ideal range is 7.4-7.6.
• Test total alkalinity of the water. Proper range is 80-120 ppm.
• Shock your spa with SpaGuard Enhanced Shock or superchlorinate with Teddy Bear Chlorinating Concentrate.

Monthly Care

• Test your water – Bring a sample to Teddy Bear Pools & Spas for analysis.
• Chemically clean your filter with Bear Strip Filter Cleaner.

As Needed

• Drain, clean, polish and refill based on usage.
•  If foaming occurs use Teddy Bear Anti-Foam.

If you have any question about these start-up instructions please call Teddy Bear Pools & Spa at 413-594-2666 or go online www.teddybearpools.com

About the Author

Bear Facts is a monthly newsletter form www.teddybearpools.com a division of Teddy Bear Pools & Spas in Chicopee, MA.

black bear and cubs in pool